The feeler pin of the second dial gauge should rest on the motor side face of the flange.
测隙规的指针应该停在传动器法兰盘靠近发动机的侧面上。
Must cause the damper plate and the floodgate frame tallies, inspects the top and bottom packing surface with the feeler gauge the gap, makes the gap to maintain in 0.1mm, when gap exceeding the allowed figure, may the pad enter the slanting iron at the back of this place floodgate frame, simultaneously
需使闸板与闸框吻合，用塞尺检查上、下密封面的间隙，使间隙保持在0.1mm以内，间隙超标时，可在该处的闸框背面垫入斜铁，同时将膨胀螺栓略为旋松，直至间隙合格为止。
Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm. Repeat it for three release levers, their gaps should be the same, after that screw up the locking nuts, and check it to make sure.
b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍。
B. Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm.
b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍
And dial gauge than feeler, its read a value accurate, but relatively difficult when the certain place of chassis is operated.
而百分表较之厚薄规，其读值准确，但是在底盘的某些部位操作时较为困难。
In implementation, a feeler gauge measures the thickness of the just-made sheet metal and sends this signal back to a servo-motor controlling the single variable of traction, the variable to affect the steel last, just before the rollers.
在实施过程中，由一个厚薄规测量刚刚制成的金属板的厚度，然后把信号传回一个伺服电动机以控制牵引力的单一变量——在卷板机之前最后影响钢板的变量。
Measure measure to choose to want correct current, measure to what car batholith cooperates clearance between each component choose feeler normally (feet of a place of strategic importance) or dial gauge.
测量量具选择要正确就目前而言，对汽车底盘各部件间配合间隙的测量通常选用厚薄规或百分表。
If you still have the lawnmower manual and a feeler gauge you can adjust the gap to the specifications.
如果您仍然有割草机手册和触角衡量您可以随时调整的差距，以规格。
When new spark plug is used or after the sidecar has been driven for 1000 km, spark plug gap should be checked with feeler gauge.
当新的火花塞使用或之后的边门一直驱动为1000公里，火花塞间隙应检查与触角gauge。
Remedy: Check valve actuator with feeler gauge; re-adjust if necessary.
检查电子管驱动部分，若有需要重新调整
A Mercedes tool kit with a few extras like a feeler gauge, spoke wrench, a file, a couple of jack knives, one of which is a Swiss Army knife, Chinese plug wrench, this means I have at least four ways to remove a plug.
奔驰工具包有一些额外像触角衡量，以扳手，一个文件，一对夫妇的杰克刀，其中之一是瑞士军刀，中文插件扳手，这意味着我已经至少有四种方法可以删除插件。
Straightedge rule (square rule, slide gauge, inside and outsidemicrometer, steel tape, feeler, dial gauge, depth micrometer, wire gage, radius gage, thread pitch gage) is a kind of common measuring tool.
直尺（角尺、游标卡尺、内径和外径千分尺、钢卷尺、塞尺、千分表、深度千分尺、线规、半径规、螺距规）是一种常用量具。
Straightedge rule(square rule, slide gauge, inside and outside micrometer, steel tape, feeler, dial gauge, depth micrometer, wire gage, radius gage, thread pitch gage)is akind of common measuring tool.
直尺(角尺、游标卡尺、内径和外径千分尺、钢卷尺、塞尺、千分表、深度千分尺、线规、半径规、螺距规)是一种常用量具。
Feeler gauge used for measuring.
测量用测隙规。
Measuring clearance reduction with a feeler gauge.
用测隙规测量游隙减小量。
After debugging the system, the feeler gauge and block gauge thickness is measured, and the result shows that the system could achieve high degree of accuracy.
研制了水面油膜厚度测量实验系统，进行了系统调试和对块规厚度测量，实验结果表明系统可以达到较高精度。
Analysis of uncertainty in micrometer measuring feeler gauge
用微米千分尺测量塞尺片厚度的不确定度分析
Programming the Measuring Software for Feeler Gauge Based on VB
基于VB的塞尺智能测量软件的开发设计
Programming the measuring software for feeler gauge figures out the problem of noting and calculating data by hand in feeler gauge measurement.
塞尺智能测量软件的开发及应用解决了以前手工记录、人工数据计算等效率低下的问题。
Quick-Feeler Assembly Used in Boring Tool setting gauge for the stand machining center
镗削加工快速对刀装置立式加工中心用对刀装置