In order for the flange joint to maintain a gasket seal.
为使法兰连接保持良好的垫片固定密封。
In order for the flange joint to maintain a gasket seal, it requires dynamic loading.
在为了使法兰接头，以维持一个垫片密封，它需要动态加载。
Mechanical joint in which sealing is obtained by applying pressure to the gasket by gland.
机械式连接采用使用压盖的方法向密封垫片施加压力获得密封效果。
Mechanical joint in which sealing is obtained by applying pressure to the gasket by gland, and permits significant angular deflextion both during and after installation and which can accept a light offset of the centreline..
机械式连接采用使用压盖的方法向密封垫片施加压力获得密封效果，在安装期间或安装之后允许有较大角度变位，并接受少许中心线偏离的连接。
Second, the joint surface of the tooth body gasket does not meet the standards.
二是阀体结合面的齿形密封垫不符合标准。
Annular flange joint surface pressure control valve for connection with lens gasket, gasket when compressed, the gasket being pressed on the flange convex U-slot form tight seal.
环形结合面法兰用于高压控制阀的连接，采用透镜垫片，当压紧垫片时，垫片被压人法兰凸面上的U形槽内，形成严密密封。
Rely on the static sealing gasket face joint logistics process will remain in the body and bonnet flange or within.
依靠端面接头垫片的静密封将工艺物流保留在阀体和阀帽内。
4 Before installation, contact wire of flange's ring type joint face and metallic ring gasket shall be checked.
6.2.4 安装前，法兰环槽密封面与金属环垫应作接触线检查。
Standard joint is a circular male and female configuration with a corrugated metal gasket.
标准连接是圆形外螺纹和内螺纹结构，配置波纹金属垫圈。
Braided packing:graphite packing, PTFE packing, carbon fiber packing, Kevlar packing, glass fiber packing; fluid sealing gasket:spiral wound gasket, graphite cutting gasket, PTFE enveloped gasket, ring joint gasket, metal enveloped gasket, corrugated gasket, soft gasket; sealing material:pure expanded graphite foil/sheet, reinforced
提供产品：各种盘根：膨胀石墨盘根，聚四氟乙烯盘根，碳纤盘根，芳伦盘根，玻纤盘根；各类垫片：金属缠绕垫，石墨高强垫，四氟包覆垫，金属环垫，金属包覆垫，波纹垫，各类软质垫片；各种密封材料：膨胀石墨卷材、板材，增强石墨板材，无石棉橡胶板。
Gasket ——Sprial wound gasket, Metal Serrated Gasket, Metal Jacketed Gasket, Ring joint Gasket, Expanded Graphite gasket, PTFE gasket, PTFE enveloped gasket, Non absestos gasket, O ring, rubber gasket.
垫片——金属缠绕垫片，金属波齿垫片，金属包覆垫片，金属环垫，高强垫片，四氟垫片，四氟包覆垫片，无石棉垫片，o型圈，橡胶垫片。
Furthermore the design rules of Flange joint and test methods for determining these gasket parameters was presented at same time.
这些规则，一个突出的创新点是在新的垫片设计参数中融入了紧密性的概念，并同时提出了使用这些参数设计法兰接头和确定它们的试验方法。
3-D Finite Element Simulation of Bolted Flange Joint Considering Gasket Nonlinearity
考虑垫片非线性时法兰接头性能的三维有限元模拟
The male and female joint confines the gasket O. D and I. D.
这种外螺纹和内螺纹连接限制了垫圈的外径和内径。
A gasket consisting of a flat ring of rubber or plastic; used to seal a joint against high pressure.
一种由橡胶或塑料的扁环组成的垫圈；用于密封抗高压的接点。
When the gasket is placed on the block and the head installed, tightening of the head bolts squeezes the soft metal so that the joint is effectively sealed.
当气缸垫装在气缸体上，然后装上气缸盖以后，气缸盖螺栓就压紧软金属垫，这样结合处就完全密封了。
The bolt bending stress was calculated and the relation of the gasket stress distribution and the joint tightness was obtained.
计算了螺栓弯曲应力并考虑了垫片应力的分布与接头紧密度之间的关系。
Theoretical and Experimental Study on A Bolted Flanged Joint with Nonlinear Gasket
具有非线性垫片的螺栓法兰连接的理论计算与实验研究
Calculative analysis of residual deformation for ring joint gasket
八角垫残余变形计算分析
A peep hole should be set up at the insulating joint in order to inspect and disposal timely the leakage from sealing ring or insulated gasket.
对绝缘接头设置渗漏观察孔，可及时检查处理密封圈或绝缘垫内的渗漏。