Results indicated storage temperature and time had significant influence on the nutrition content of the pupae.
结果表明，经不同时间和低温贮存后，黄粉甲蛹体内的营养物质含量变化差异显著。
In order to allow Ni catalyst work at a mild temperature with little sintering and carbon formation, the influence of composition of reformer inlet gas on reforming temperature at a certain space velocity and conversion of feed CH4 was studied. At the same time, a method of changing inlet gas composition by introducing circulating gas into the feed gas was also discussed.
为了使Ni系催化剂在不易发生烧结积炭的温度下工作，分析了在一定原料CH4空速和转化率下人口气体组成对重整工作温度的影响，并探讨了在原料气中导入循环气来改变重整人口气体组成的方法。
In the paper, the influence of amino nitrogen, acidity, dissolved oxygen and temperature upon fish and vegetable in their different growing stages is investigated.
本文介绍了运用生态学原理和环境条件监控手段建立起来的、符合可持续发展要求的设施渔业新技术-鱼菜共生技术，该技术涉及养殖水系营养物质循环流动。
In this paper, The influence of heat set and dyeing on the structure of PTT fiber was investigated by FT-IR, DSC, critical dissolution time. The influence of heat set on the dyeability of PTT fiber was discussed, too. Meanwhile, many experiments on the dyeing performance of PET fiber were carried out. The effect of different dyeing temperature on the uptake and visual color depth value and dyeing characteristics of different dyes with temperature increasing were discussed, and the influence of temperature on the dyeing depth were also evaluated when dyeing for PTT and PET fiber in the same dye bath condition. Especially the kinetics and thermodynamics of dyeing with disperse dyes were mainly studied.
目前，我国对PTT染色性能方面研究报道还少，本文用傅立叶红外光谱、差热分析、临界溶解时间等分析方法研究了热定型和染色对PTT纤维结构的影响，探讨了热定型对PTT纤维可染性的影响，同时进行了多项PTT纤维的基本染色性能试验，探讨了不同染色温度对上染百分率及表观色深值的影响、不同染料的升温上染特性、不同染料的移染性能和染深性能以及PTT和PET纤维同浴染色时染色温度对它们的染色深度的影响。
Firstly, we study the influence of temperature on linear and weak nonlinear response of metal-dielectric granular composite.
研究了金属-电介质颗粒复合体线性和弱非线性的温度效应。
Test results show that board density, glue addition and type of particle had significant influence on physics and mechanics properties of SPB. Under the conditions that the hot-pressing temperature was 180℃, curing agent was 1.5%, water-proofing agent was 1%, hot-pressing time was 30s/min, the mechanical properties of SPB could meet the national standards through adjusting board density and glue consumption.
试验结果表明：板材密度、施胶量以及刨花类型对荻草刨花板的物理力学性能的影响具有显著性，在热压温度为180℃、固化剂添加量为1.5%、防水剂添加量为1%、热压时间30S/min时，通过调整板材密度和施胶量能够使压制的荻草刨花板的力学性能满足国家标准的要求。
The influence of casting velocity on the distribution disciplines of casting roll temperature and hot deformation was analyzed.
给出了浇铸稳定阶段的结晶辊温度场分布和热变形规律；分析了浇铸速度对结晶辊温度场和热变形的影响。
The paper describes the study of influence of sintering temperature and other processing technologies on the physical properties of the cemented carbide sprayed powder.
本文探讨了烧结温度及其他加工工艺对硬质合金喷镀粉物理性能的影响。
The influence of operation conditions including temperature, pH and loading ratio on the deposition rate and coating quality is investigated.
考察了施镀过程中温度，pH值和装载量等工艺条件对镀层质量及沉积速度的影响。
It had been discussed about the synthesizing scheme of predecessor about diethyl zinc used in the method of sol-gel, problems existed in it also were pointed out. Such factors caused influence to the granularity of zinc oxide powders had been systematically investigated as temperatures and times of hydrolyze reaction, the kinds and amount to be used of exterior dispersant, the value of pH, the Moore ratios of raw materials, the temperatures and times of calcinations, it had been indicated by the results that under the conditions of the Moore ratio of raw materials was 1 to 1.25, the temperature and time of hydrolyzing reaction was 80 C and 4hours respectively, PHSA used as exterior dispersant and the amount of which was 0.35%, the value of pH was 7.0, the predecessor of zinc hydroxid could be prepared out. Under the circumstance of the best calcination technics, the temperature and time of calcination was 700 C and 2.5 hours respectively, nanometer zinc oxide had been prepared.
试验探讨了溶胶—凝胶法中前驱体——二乙基锌的合成方案，并指出了其存在的问题所在；系统地考察了均匀沉淀法中的影响因素，如溶液水解反应温度、水解反应时间、表面分散剂的种类、表面分散剂的用量、溶液水解pH值、原料摩尔配比、焙烧温度和焙烧时间对氧化锌粉体粒径的影响，结果表明：在原料摩尔配比n[Zn(CH_3COO)_2]：n=1：1.25；水解反应工艺条件为：80℃×4h；以PHSA作表面分散剂，且其用量为0.35％；用酸、碱调整溶液pH值为7.0条件下可以制得前驱体Zn_2，前驱体氢氧化锌的最佳焙烧工艺制度为：焙烧温度700℃，焙烧时间2.5h。
The results show that the calcining temperature and the calcining time influence significantly the activity of nanoparticles of MgO.
若MgO结构松弛、存在晶格畸变、缺陷较多，则表现为活性较高；反之，如果MgO晶粒较大、结构紧密、晶格完整，则其活性较低。
Horizontal continuous casting systems of pilot scale were designed to produce copper-nickel tube blanks. The method of casting-rolling to produce BFe10-1-1 condenser tubes was investigated for the first time in our country. According to the solidification character of BFe30-1-1 tube blanks, numerical simulation computation model of temperature field was established for simulating heat transfer during continuous casting. The influence of parameters on the solidification of BFe30-1-1 tube blanks were investigated, and BFe30-1-1 tube blanks were obtained by horizontal continuous casting.
建立了一套中试规模的空心白铜管坯水平连铸实验装置，在国内首次采用铸轧法制备BFe10-1-1合金冷凝管；根据BFe30-1-1合金空心管坯连铸过程的凝固特点，建立了连铸过程温度场数值模拟计算模型，考察了工艺参数对BFe30-1-1合金空心管坯成形的影响规律，获得了高质量的BFe30-1-1合金水平连铸空心管坯。
Amorphous Co-Ni-P thin film had a lower coercive force and higher squareness ratio. The values of its coercive force and squareness ratio increased when the film was crystallized. Coercive force and squareness ratio of the film which was made up of α-Co and phase of Co2P reached their peak values under the influence of much phosphorous segregating at crystal boundary when heated to 500℃ 1 hour. As temperature was increased successively, the coercive force and squareness ratio of the film decreased because of grain growth and second phase coarsening.
非晶态Co-Ni-P薄膜的矫顽力较低，矩形比较高；薄膜向晶态转变时，矫顽力和矩形比皆呈上升趋势；500℃×1h热处理，薄膜由α-Co和Co2P相构成时，且在晶界上偏聚较多磷的影响下，矫顽力和矩形比的值达到最高；温度继续升高，晶粒长大，第二相粗化时，薄膜的矫顽力和矩形比都减小。
It is proposed that to control only surface temperature of radiator in radiant heating design is not enough, and the comprehensive consideration should be given to the influence of surface temperature of radiator and back temperature of radiator in adjacent room on the room comfort.
提出了在辐射供暖设计中，单一控制辐射体表面温度是不够的，必须综合考虑辐射体表面温度和邻室辐射体背面温度对房间舒适性的影响。
Lastly, those shortages of current chemorheology models are put forward, while it is anticipated that the widely applied chemorheology model about the combined influence of temperature and cure degree will be research hotspots in future.
最后分析了现有化学流变模型的不足，指出综合考虑温度和固化程度因素、适用范围更广的化学流变模型将是未来的研究重点。
Some factors such as water, surfactants and temperature had important influence on it.
水分及表面活性剂、温度等因素对电导率有重要的影响。
Recrystallization temperature and microstructure and influence of microstructure on phase transformation and tensile strength of hot-rolled TN479 shape memory alloy rod with a diameter of 19mm were systematically investigated in terms by optical microscope, Vickers hardness tester and differential scanning calorimetry and tensile tester.
利用光学显微镜、维氏硬度计、差热分析仪和拉伸机，系统研究了直径19mm的TN479合金热轧棒材的再结晶温度和显微组织，以及显微组织对相转变和拉伸强度的影响，以便为该合金在工程上的应用提供理论依据。
Based on the principle of wax deposition, it is inferred that the wax will deposit on the internal surface of prover when ambient temperature and pipe wall temperature are low, which will influence the indication errors of flow.
根据原油在管壁内结蜡的理论，推断出当环境温度、管壁温度较低时体积管标准管段内将会结蜡，结蜡厚度对流量计在线检定时的示值误差将有不同程度的影响。
The influence of curing reaction heat on curing temperature field of cubic rubber block and tire was investigated.
探讨长方体胶块和轮胎硫化反应热对硫化温度场的影响。
The frictional characteristics of the rubber block were analyzed, the influence of ambient temperature on the friction coefficient was discussed.
所用方法可应用于其它材料在冰面上的摩擦及其它情况下的摩擦熔化问题。