In this research at first the six factors affecting rainfall were chosen, as the input variables. They are the minimum atomospheric pressure, maximum wind velocity near typhoon center, move speed of typhoon center, the radius of typhoon, the shortest distance between typhoon center and Taipei monitoring station, station humidity.
本研究先选取影响台风雨之因子，选用钟型函将中心最低气压、近中心最大风速、移动速度、暴风半径、台风中心距测站最短距离、测站湿度做为六个输入变，建模糊属函。
Its objective is to improve mechanism performance by varying the speed trajectories of the input link actively.
变输入转速机构的设计目标是藉由主动地改变输入构件的转速轨迹来改善机构的性能。
The card used external triggering signals and impulses or internal triggering signals to initialize card behaviors. Two pieces of 142bitA /D converter chipsADS5547 enabled a crossing sampling rate of 420MSPS to a single analog input signal or a non2crossing sampling rate of 210MSPS to two signals from the two channels. The digitalized data, afterDSP, were cached on the card memory to be analyzed further through digital storage oscilloscope designed in software, otherwise stored into the high2speed hard disk through HSHD interfaces.
该数据采集卡采用外部或者内部2种触发方式，利用2片14位模数转换芯片ADS5547，对一路模拟信号进行双通道交叉采集可获得420MSPS的采集速率或以210MSPS速率对2路不同的信号交叉采集；采集到的数字信号经过数字信号处理，缓存于数据采集卡并通过数字存储示波方式实时查看，或者选择硬盘存储方式进行数据的大容量存储。
Any child has not been read out of the baggage scanner will be sorted according to the manual coding, the input data manually, the speed of 10-20 cases per minute.
任何未被子扫描器读出的行李都将被分拣到人工编码点，由人工输入数据，速度是每分钟10-20件。
The effect of input angular velocity, angular acceleration and driving speed to Coriolis effects was analyzed by ANSYS software.
利用ANSYS软件仿真分析了输入角速度、角加速度及驱动速度对哥氏效应的影响。
The amount of energy for latent heat released and ultrasound speed measured at the zone of maximum ice crystal formation were respectively about 72% of total input energy and 63.64% of ultrasound speed range during the freezing process.
试验结果显示，牛肉在冻结过程的中心温对应时间曲线中，冻结点附近潜热特性明显，在 0 ~- 5 ℃之间则冰晶最大生成带特性明显。
A new method of improving shift quality of AMT with the fuel stop valve was indicated, the efforts to the shift quality at different input shaft and output shaft of clutch were analyzed, the control strategy was established, and the test on one kind of AMT heavy truck was conducted. The test result showed that it could decrease the rotational speed between the drive part and the driven part when clutch was locked, and improve the shift quality of AMT with control of the fuel stop valve.
提出了利用断油电磁阀改善AMT换挡品质的方法，分析了断油电磁阀不同断油和供油时刻对换挡品质的影响，制定了断油电磁阀的控制策略，并在装有AMT的某重型载货汽车上进行了试验，试验结果表明，换挡过程中通过控制断油电磁阀，可以减小离合器接合时主、被动部分的转速差，显著改善了AMT的换挡品质。
In order to improve dynamic performances of variable speed constant frequency in constant power output running area, research situation of variable pitch control is studied, based on RBF neural network tuning PID control, wind turbine and variable pitch control model is built, generator rotate speed measurements and speed error as input contoller.
中文摘要：为了改善变速恒频风力发电系统在恒功率输出运行区域内的动态性能，在分析系统变桨距控制研究现状的基础上，基于RBF神经网络整定PID控制理论设计风力发电系统变桨距控制器，建立了风力机及变桨距机构模型，以发电机转速测量值与额定转速相比后误差为输入设计控制器。
But with the appearance of net PY input method which speed is more faster and easy to learn and use than Wubi. It looks like to replace the Wubi input method.
但随着网络拼音输入法的出现，其输入速度和易用易学性都不亚于甚至超过了现有的五笔输入法，大有完全取代之势。
First of all, the energy saving control of hydraulic excavator in China and aboard are related, and the control methods are summarized in this paper. For the sake of energy saving control research, a hydraulic excavator electronic energy-saving control model is established based on CAN-bus technique. And then the aspect of the speed control of the engine is focused on, a cascade control is used, an inner feedback loop gives control over the governing throttle and an outer feedback loop does the speed regulation. The use of feed forward of the load demand, when a signal is available which is proportional to the load, then the signal can be fed forward to the input of the control system to anticipate changes in load. The power limiting control ensures optimum use of the power required for the excavator under varying operating conditions and avoids overload of the diesel engine, with the diesel engine, variable pump, and the loads as the whole dynamic system, the overall power match technique is proposed, and transfered the point match to area match by the method of area power match, so the energy efficiency is improved.
本文首先综述了国内外液压挖掘机节能控制的发展现状，并对当前所采用的节能控制方法进行了总结；为进行节能控制研究，建立了基于CAN总线技术的挖掘机电子节能控制系统；然后对挖掘机在不同工况下工作时发动机转速的控制进行了研究，采用转速和油门位置双闭环改进PID控制及负载前馈控制方法，将一个与负载成比例的信号前馈到控制系统的输入端，补偿抑制负载变化对控制输出的影响，使发动机的转速始终保持在某一允许范围内，从而使发动机始终工作在某一指定的工况；针对柴油机经常因特性的变化而导致负载扭矩超载的现象，采取了功率极限控制，既可以防止发动机失速停车，也可以取消功率储备，充分利用柴油机额定功率；最后将发动机、变量泵及负载作为一个动态系统，设计了挖掘机全局功率匹配方案，并提出区间功率匹配控制方法，改变了以往动力系统静态模式设定的缺点，使挖掘机在最佳节能区间内工作。
Some signal rate of automotive electronics equipment changes very fast, and many fault signals are intermittent, which requires the test equipment run faster than the speed of fault signals. Digital oscilloscope can be fully competent with this rate, and also it runs faster than any other car tester. Its high sampling speed can precisely display input and output components of the situation, besides, it also shows noise or intermittent fault that the components or line make.
汽车电子设备的有些信号变化速率非常快，许多故障信号是间歇的，时有时无，这就需要仪器的测试速度要高于故障信号的速度，数字示波器完全可以胜任这个速度，且比其他的汽车检测仪还快，高取样速度可以精确详实地显示输入、输出元件的状况，不仅如此，也可以显现出元件或线路的噪声或间歇性故障。
The multiple cells FDTD formulations of many kinds of lumped circuit elements were derived, which are in highly accordance with practical circuits. These formulations were applied for hybrid electromagnetic systems and the respondences to high-speed input pulse were obtained directly.
在集总元件的单网格FDTD模型基础上，根据实际电路的要求，推导了各种线性和非线性、无源集总元件的多网格三维FDTD迭代格式，并参与分布电磁系统的电磁场模拟。
You will select rotation direction, winding type, wire position, pitch, input and output, winding speed, heating temperature...
你会选择旋转方向，蜿蜒型，线材的立场，音高，输入和输出，清盘速度快，加热温度。。。
This system uses a MCU as a core, a keyboard and infrared detecter as the input system, a LED display circuit, a warning circuit and a stepper motor as the output system to realize the auto controlling of the liquid drop speed.
本次设计的系统，是以8031单片机为核心以键盘及红外传感器为输入系统，以数码管、报警电路及步进电机为输出系统的智能化的液体点滴速度的控制及监测系统。
It turns out that the implementation of improved serial structure consumes resource least but the filter speed is low, and the parallel structure has a fastest filter speed but consumes resources most. Whereas, the filter speed of DA struc-ture only depends on the width of input data, so its filter speed is usually faster than improved serial structure but the con-suming resource is less then parallel structure.
结果表明，改进串行结构的实现消耗资源少但滤波速度慢，并行结构的实现滤波速度快但消耗资源多，而DA算法的实现速度仅取决于输入数据的宽度，所以滤波速度通常较快且消耗的资源较少。
The mathematic models were built by using load as input and pressures of hydraulic cylinder chambers as output in the metering-out speed control system with flow control valve, and this system would be simplified as a stable second-order system, and the changing rules of overshoot were obtained.
针对回油路串接调速阀的调速阀出口节流调速系统，以负载作为输入，液压缸有杆腔和无杆腔压力作为输出，分别建立了系统的数学模型，系统可简化为稳定的二阶系统，得到了液压缸两腔压力超调量的变化规律。
The last but not least, it is also owning to the rapid development in computer science and information technology. Such as, some computational task, which previously must be executed by using super-computer, now can be carried out by personal computer, and at the same time, the network speed and band width of data bus and input/output equipment have increased several times. In addition, the improvement of the high quality graphic displaying is available. All these provide strong support for cryoEM high-resolution reconstruction study.
目前，在低电子剂量的情况下，冷冻电镜照片可以记录到3-4 〓的信息，使用冷冻电子显微镜进行高分辨三维重构工作，已经获得6.5-8〓高分辨率水平的结果，可以分辨出蛋白质的α螺旋、识别出蛋白质的β折叠等蛋白质二级结构；其次是，三维重构算法效能的不断提高，使得对二十面体取向和中心参数计算的可靠性大大提高；再次是，由于计算机和信息技术迅猛发展，例如，以往需要使用大型计算机的计算任务已经可以被一般的个人电脑完成，网络速度、数据总线和硬盘等I／O设备的带宽成倍增长，以及图像显示能力的提高都为冷冻电子显微镜高分辨三维重构技术提供了强有力的支持。
Nowadays, in the low electron dose condition, the information about 3-4〓 can be recorded on the cryoEM micrograph, and the high-resolution reconstruction using the cryoEM has reached 6.5-8〓 levels. The reconstruction can reveal the protein α helical and recognise β fold secondary structure. Secondly, it is due to the development in 3D reconstruction method, which can be more efficient to determine the orientation and center parameters. The last but not least, it is also owning to the rapid development in computer science and information technology. Such as, some computational task, which previously must be executed by using super-computer, now can be carried out by personal computer, and at the same time, the network speed and band width of data bus and input/output equipment have increased several times. In addition, the improvement of the high quality graphic displaying is available. All these provide strong support for cryoEM high-resolution reconstruction study.
目前，在低电子剂量的情况下，冷冻电镜照片可以记录到3-4 〓的信息，使用冷冻电子显微镜进行高分辨三维重构工作，已经获得6.5-8〓高分辨率水平的结果，可以分辨出蛋白质的α螺旋、识别出蛋白质的β折叠等蛋白质二级结构；其次是，三维重构算法效能的不断提高，使得对二十面体取向和中心参数计算的可靠性大大提高；再次是，由于计算机和信息技术迅猛发展，例如，以往需要使用大型计算机的计算任务已经可以被一般的个人电脑完成，网络速度、数据总线和硬盘等I／O设备的带宽成倍增长，以及图像显示能力的提高都为冷冻电子显微镜高分辨三维重构技术提供了强有力的支持。
In the construction above, the first unit (70) and the second unit (100) are individually assembled first and then the drive device (10) is assembled by coupling the output shaft (96) of the power distribution mechanism (16) and the input shaft (104) of the automatic speed changer (20), and as a result, workability in assembly is improved.
在以上构造中，首先单独组装第一单元(70)和第二单元(100)，然后通过连接动力分配机构(16)的输出轴(96)和自动变速器(20)的输入轴(104)来组装驱动装置(10)。由此提高了组装效率。
In order to raise measurement speed and accuracy of winding direct current resistance, step input dynamic test method is put forward in this paper.
为提高绕组直流电阻的测量速度和精度，本文提出了阶跃响应动态测试法。