Now the main products include:crank arm manual and electric flexible awing series; track type electric velarium series; exhibition folding series; sunshade, luxurious wood umbrella and side_hanging umbrellaseres; fixed and mobile French ball type, triangle type, trapezoid type and arch awnigns. The products have been widely used in exhibition, amusement park, villa area, various high level hotels, restaurants, bars, coffee shops, apartments, holiday resorts, recreational plaza, swimming pools, bathing places, gourmet streets, kindergartens, schools, outdoor temporary activities as well as balconies, terraces and sun houses of hotels and apartment buildings as well as other leisure places etc. for their novel and unique design, well selected material, elegant profile and reliable quality.
目前主要产品有：曲臂式手动，电动伸缩遮阳篷系列；轨道式电动天幕系列：展览活动折叠系列；太阳伞、豪华木伞、边吊伞系列；固定、活动法式球型、三角型、梯型、圆拱型篷系列；产品因设计造型新颖独特、选材精良、美观大方、质量可靠，而广泛应用于展览会、游乐园、别墅区、各类高档宾馆、餐厅、酒吧、咖啡厅、公寓、休闲度假旅游区、休闲广场、游泳池、海滨浴场、美食街、幼儿园、学校等户外临时活动以及酒店、公寓楼的阳台、露台、阳光屋等休闲场所。
Opposite the side arm is the crank attached to a ground joint which is used to raise or lower the heater.
对面的方 ARM是曲柄附加到地面的联合是用来提高或降低加热器。
The crank arm with the chainring and guard will be mounted on the LEFT SIDE.
曲柄臂与chainring和警卫将安装在左侧。
View showing one way of attaching crank note that crank has been removed and reinserted into crank tube to enable the crank frame to be rotated 180 degrees and still have the chain drive on the right side.
检视显示单程附加曲轴曲柄注意到，已删除和重新融入曲柄管，使曲柄范围内，以180度旋转，并仍然有链传动的右侧。
Through analysis of simulation results, found the center mass of crank and linear eccentricity have big influence to piston side pressure and inertia force.
然后在Pro/E中建立S195柴油机曲柄连杆机构的虚拟样机模型，导入ADAMS中进行动力学分析，绘制出虚拟样机模型中各连接位置处动力仿真结果曲线。
The involute energy saving pumping unit demands large crank offset angle and wide torque adjustment range, therefore a single-side asymmetric adjustment crank structure is put forward.
针对渐开线节能抽油机对曲柄的大偏置角、扭矩调整幅度大等要求，提出了非对称单侧调整的曲柄结构设计方案，给出了结构设计原理和注意事项。
This paper described work principle and structure design of side cut punch composite mold and assembly testing requirements using the crank press machine.
介绍了在曲柄压力机上切边冲孔的复合模结构设计、工作原理及装配和调试要求等。
Here I have tires, saddle and crank arm from the scan of a side view photo. I clean them up a bit. I do some rendering over the top to try and get rid of the grain of the photo scan.
我手头有一个从照片上扫描的轮胎，座鞍和脚踏曲柄的侧面，所以我稍做修改去除杂点直接就用上了。
The on-site use of over 30 involute energy saving pumping units proves that: (1) the single-side asymmetric adjustment crank structure is suitable for the crank with large offset angle, and the crank with this structure has light weight and wide torque adjustment range;
30余台渐开线节能抽油机的现场使用证明：（1）非对称单侧调整曲柄结构适应偏置角较大的曲柄，具有总体质量轻、平衡扭矩调节幅度大等优点；
A beam that connects the piston rod to the connecting rod of a reciprocating engine. back-side-crank pumping unit
十字头连接活塞杆和往复式发动机连杆的横杆
Discussion on Extreme Position Angle of Mono side swing Type Crank rocker Mechanism
关于单侧摆动型曲柄摇杆机构极位夹角的探讨
Revised Design of Radial Tool for Crank Web Side
曲柄臂侧面圆角车刀的改进设计
It has a crank on one side, and a spool on the other.
它有一个曲柄一方和缓冲为另一方。
One end of the push crew is put on a bracket, and the other end is extended out of one side of the stove body and connected with a crank.
推料螺杆的一端架在支架上，推料螺杆的另一端突出于炉体一侧，并与摇把相连接。