To lessen the resonance from the HDD I used rubber rings to mount it in place.
为了减少从硬盘我用橡胶圈装入到位的共鸣。
Machinery parts, auto parts, bearings, filters, control arm, rubber parts, suspension, wheels, machining fittings, car parts, bearing, filter, control arm, engine mount, suspension, hub, shaft, rod, shaft, rod all are our Main Products. Zhedong Trading Co., Ltd.
机械配件、汽配、轴承、滤清器、控制臂、橡胶件、悬挂、轮毂、machining fittings、car parts、bearing、filter、control arm、engine mount、suspension、hub、shaft、rod、轴、杆是浙东贸易有限公司的主营产品。
The thesis took the engine-transmission assembly as a six-degree-freedom rigid body, established its physical and mathematical models based on analyzing the dynamic performance of rubber mount. The system's parameters are measured by experiments, including the center of gravity, the inertia and the mounts'stiffness, and then programmed the VEHMA software, which is abbreviated from Vehicle Mounting System Analysis.
本文将动力总成视为六自由度刚体，在分析橡胶悬置动力特性的基础上，建立了动力总成悬置系统的力学及数学模型，对该系统的质心位置、转动惯量、悬置刚度等基本参数进行了测量，并利用面向对象的编程技术，编写了VEHMA软件，即Vehicle MountingSystem Analysis。
Oil pan, Oil Pipe, Rubber Hose, Water tube, Valve Seal, Washer, Waterproof ring, Stop-Ring, Dustproof cover, Ripple tube, Bonded seals, Seal cover, Seal holder, Bearing sleeve, Handle, Bushing, Bushing Block, Pad, Gasket, Rubber Spring Gasket, Boot, Blade, Socket, Grommet, Nut, Clip, Housing, Gauze, Dust cap, Buffer block, Isolation block, Piston, Piston ring, Strainer, Rotary seal, Frictional damping washer, Combination Seal Gasket, Axis guide, Water blocking, Torque core, Repair kits, Hydraulic Seal, Engine Seal, Engine Mount, Seal Circle, Spring(Compression spring, Tension spring, Disc spring), Compressor parts, Brake parts, Air valve parts, Rubber mountings, Strut mount, Control arm mount, Connecting rod, Control Arm Mount, Full Set Repair Kit, Asbestos pad, non-asbestos pad, Casting aluminium, Casting copper, Casting steel, and other relative product etc, .
本厂主要产品包括油封(气门油封、骨架油封、铁壳油封、浮动油封、同步油封、异型油封)、密封圈(O型密封圈、U型密封圈、Y型密封圈、X型密封圈、W型密封圈、V型密封圈、L型密封圈、星型密封圈)、油管、水管、水封、摇把、把手、拉手、胶碗、垫片、平垫、纸垫、组合垫、牛筋垫、牛津圈、密封垫、垫圈、档圈、格莱圈、牛筋圈、防水圈、防尘圈、防尘罩、防尘套、轴套、衬套、卡套、平叉套、缓冲套、锥形套、活塞、活塞环、支承环、导向环、导向带、缓冲套、缓冲垫、缓冲圈、缓冲块、隔振块、减震块、油底壳、滤网、呼吸片、伐片、叶片、起动绳、机轮爪、六角密封圈、导承圈、密封涨圈、纸垫、石棉垫、非石棉垫、弹簧等橡胶塑料制品以及铜、铁、铝、粉末冶金等冲压和铸造件。
Oil pan, Oil Pipe, Rubber Hose, Water tube, Valve Seal, Washer, Waterproof ring, Stop-Ring, Dustproof cover, Ripple tube, Bonded seals, Seal cover, Seal holder, Bearing sleeve, Handle, Bushing, Bushing Block, Pad, Gasket, Rubber Spring Gasket, Boot, Blade, Socket, Grommet, Nut, Clip, Housing, Gauze, Dust cap, Buffer block, Isolation block, Piston, Piston ring, Strainer, Rotary seal, Frictional damping washer, Combination Seal Gasket, Axis guide, Water blocking, Torque core, Repair kits, Hydraulic Seal, Engine Seal, Engine Mount, Seal Circle, Spring(Compression spring, Tension spring, Disc spring), Compressor parts, Brake parts, Air valve parts, Rubber mountings, Strut mount, Control arm mount, Connecting rod, Control Arm Mount, Full Set Repair Kit, Casting aluminium, Casting copper, Casting steel, and other relative product etc, .
本厂主要产品包括油封(气门油封、骨架油封、铁壳油封、浮动油封、同步油封、异型油封)、密封圈(O型密封圈、U型密封圈、Y型密封圈、X型密封圈、W型密封圈、V型密封圈、L型密封圈、星型密封圈)、密封条、油管、水管、水封、拉手、胶碗、垫片、平垫、组合垫、牛筋垫、牛津圈、密封垫、垫圈、档圈、牛筋圈、防水圈、防尘圈、防尘罩、防尘套、轴套、衬套、卡套、平叉套、缓冲套、锥形套、活塞、活塞环、支承环、导向环、导向带、缓冲套、缓冲垫、缓冲圈、缓冲块、隔振块、减震块、油底壳、滤网、呼吸片、伐片、叶片、起动绳、机轮爪、六角密封圈、导承圈、密封涨圈、纸垫、石棉垫、非石棉垫等橡胶塑料制品以及铜、铁、铝、粉末冶金等冲压和铸造件。
Our factory has a variety of high-precision digit-controlled lathes. Special research and develop auto swinging arm, Suspension? Ball Joint. Tie rod end. Auto exhaust pipes and rubber mount etc.
本厂有各种高精密度数控车床数台，数台塑料压塑机和吹塑机，高吨位的橡胶机，专业生产研发汽车摆臂，悬挂球头，拉杆球头，汽车废气管和橡胶件等。
A bridge supported by trestlework. Depending on the mileage and operating conditions of the vehicle, this could result in the rubber mount coming completely free from the shock absorber.
一座靠支架支撑的桥。因汽车的行驶里程和使用条件而异，可能导致橡胶支座与减震器完全脱离。
Through the test method of a certain type of hydraulic mount and mount rubber Lord spring of dynamic stiffness and the frequency of the lagging Angle of change and change characteristics, and will both static and dynamic stiffness, lagging Angle, comparing the difference between are analyzed.
通过试验方法研究了某型液压悬置及悬置橡胶主簧的动刚度和滞后角的频变和幅变特性，并将两者的动静刚度、滞后角进行对比，分析两者之间的差别。
There are certain limitations about the conventional rubber mount in the isolation characteristics, the engine mount requirements of the low dynamic stiffness on high-frequency vibration and damping of high on low-frequency vibration is actually a pair of contradictory body.
常规的橡胶悬置在隔振特性上存在着一定的局限性，对发动机悬置在高频振动时具有低的动刚度，低频振动时具有高的阻尼系数的要求实际上是一对矛盾体。
Keeping the original structure and changing the structural parameters of main rubber spring and metallic skeleton, the effect of these parameters on hydraulic strut mount is determined by finite element simulation.
在保持其原有结构形式基本不变的前提下，变动减振支座橡胶主簧以及金属骨架的结构参数，利用有限元数字仿真确定了这些参数对液力减振支座刚度的不同影响程度。
Through the establishment of rubber mount and engine mounting system model the mechanical model, the incentive of mounting system, vibration isolation performance analysis; and through the method of testing the vibration isolation mounting system performance is analyzed.
通过建立橡胶悬置模型和发动机悬置系统的力学模型，对悬置系统进行了激励分析、隔振性能分析；并通过试验的方法对悬置系统的隔振性能进行研究。
The most of isolators which are used for automobile engine are passive rubber mount, while the passive hydraulic isolator is applied for top grade car.
目前汽车发动机使用的隔振装置多为被动式橡胶隔振块，中高档车则采用被动式液压悬置。
Rubber mount and hydraulic mount are applied widely to engine mount at present and their performances of vibration isolation are not good enough, so semi-active mount of good performance is paid more attention by many researchers.
目前发动机悬置大多数采用的是橡胶悬置或液压悬置，其隔振性能还不能令人满意，性能优良的半主动悬置受到了众多研究者的重视。
For a practical rubber engine mount, empirical formulae are established which vary with compression level.
结合车用发动机悬置，计算得到了橡胶悬置在不同变形量情况下形状系数的经验公式。
Hydraulically damped rubber mount (HDM) is a kind of advanced vibration isolator for automotive powerplants and other dynamic systems.
液阻型橡胶隔振器是汽车动力装置等系统的先进隔振元件。
Study on the drift of rubber mount
橡胶隔振器蠕变特性研究