Automatic monitoring feature:enabling the equipment to be halted in the event of abnormal condition.; Including 5 main menus as follows: Capacity:pre-setting capacity and displaying amount processed System:setting parameters:A. total feed sections; B. feed speed; C. inching speed; D. acceleration time/deceleration time; Length:feed length and feed frequency of each section; Monitoring:displaying setting/current values of number of feed sections, feed length and feed frequency; Abormity:showing abnormal informationabnormal display page will pop up in case of abnormal condition
据有自动临生产过程功能，出现异常状况自动停止生产包含以下5个主画面。产量：预设定生产数量和显示已加工的数量系统：用于设定：A送料总段数；B 送料速度； C寸运速度；D 加减时间。长度：各段数的送料长度和送料次数。监视：用于显示送料段数，送料长度，送料次数之设定值与现在值；异常：显示异常讯息内容（如有异常状况将自动跳出异常显示页，显示异常状况
Mass transfer and heat transfer through hydrophobic microporous membrane in sweeping gas membrane distillation was studied. A model about heat and mass transfer was constructed and solved. The effects of sweeping gas velocity, module length, feed flux and feed temperature on membrane flux were tested.
对气扫式膜蒸馏的热量和质量传递机理进行了研究，建立了该过程的热量和质量传递模型，并对模型进行了计算，得出了吹扫气流速、组件长度、进料流速和进料温度对膜通量的影响。
The variables subject to control include the bowl diameter, length, and speed; the ramp slope and length; the pool depth; the scroll speed and pitch; the feed point of sludge and chemicals; the retention time; and the sludge conditioning.
有多种可变的因素需要控制，其中包括碗的直径，长度和转速，斜面的坡度和长度；池子的深度，转轴的速度和声音；淤泥和化学药品的留入口，保持力的时间和淤泥的条件作用。
The best results occurred when the moisture content of straw is 12~14%, the length of straw is smaller than 10mm, the rotational velocity of the screw feed is 35~36rpm, and the forming temperature is 240℃. Besides, adding an mandrel on the screw as well as smoothing the surfaces of dies and the screw can also help straw forming.
归纳螺杆挤制机挤制稻草实验结果，稻草可成型的最佳条件为──稻草长度小於10mm、稻草含水率12~14%、成型温度240℃、挤制螺杆转速35~36rpm，另外，增加螺杆中心轴与提高模具、螺杆的表面光滑度，也都可以帮助成型。
The results showed that the shrimp fed the diets containing(8.78%) to 17.82% of squid liver had significantly higher body length and body weight, indicating that squid liver may partially substitute fish meal and increase feed efficiency.
结果表明，饲料中用鱿肝脏替代部分鱼粉、玉米粉，能提高饲料的诱食性及利用率，也能提高凡纳滨对虾体长与体重的增长率，且直接添加湿鱿肝脏并经挤压生产的虾饲料能保持鱿肝脏脂肪酸的不饱和度组成，较添加鱿肝脏粉的饲料营养价值高。
Motion control features include: cutter radius and length compensation, path deviation limited to a specified tolerance, lathe threading, synchronized axis motion, adaptive feedrate, operator feed override, and constant velocity control.
运动控制属性包括：刀具半径和长度补偿，轨迹误差限制，车削螺纹，轴同步运动，自适应进给率，操作者过度进给和恒定速度控制
Feed a fair amount through so that you still have a good length of loop to work with.
饲料相当数量通过，这样您仍然有一个很好的长度循环工作。
To extend the length of time baby can go through the nigh without waking for a feed try introducing a dream feed.
延长的时间长度的婴儿可以继续通过几乎没有唤醒一个饲料尝试引入一个梦想的饲料。
A Doherty-feed-forward power amplifier for improving the efficiency and linearity was presented. Influence to the amplitude, the phase and the time delay mismatch of the feed-forward system has been analyzed, and the efficiency factor and the method of efficiency enhancement is discussed. Also the peaking amplifier bias and influence of peaking compensate line length to peaking efficiency point is analyzed. Finally the LDMOS field-effect transistor is used to design the Doherty-Feed-forward power amplifier, compared with the balance structure Feed-forward amplifier, simulation result shows its efficiency enhanced 5% when IMD3 is -65dBc.
将前馈技术与Doherty技术相结合，以满足功率放大器在效率和线性度方面的要求，同时对前馈系统幅度、相位、延时不平衡的影响进行了分析，就其效率因素和增强效率的方法进行了讨论；还分析了Doherty功率放大器中峰值放大器的栅极偏压V(下标 gs和峰值补偿线长度对获得峰值效率点的影响，最后把用LDMOS管设计的Doherty功放作前馈系统的主功放，与平衡结构作主功放的前馈系统相比较，仿真结果显示IMD3达到-65dBc时，其效率提高了5%。
The use of serrated cutting edge: the use of serrated cutting edge to chip breaking to fine crumb; so that the direction of cutting forces scattered, inhibit the occurrence of high-frequency vibration; serrated cutting edge and workpiece contact length than the regular circular blade machine clip-on-li Milling longer can chip thinning to improve the feed per tooth.
采用锯齿形切削刃：采用锯齿形切削刃能将切屑分断为细屑；使切削力方向分散，抑制高频振动的发生；锯齿形切削刃与工件的接触长度比普通圆刀片机夹式立铣刀更长，可使切屑变薄，从而提高每齿进给量。
In this embodiment, the feed conductor 106 is part of the antenna length.
在该实施例中，馈送导体106是天线长度的一部分。
Feed the animals by hanging a piece of raw meat on a length of thread.
把生肉吊在一根绳子上给那些动物吃。
Single-needle lockstitch flat bed machine with bottom feed, needle feed and alternating feet and a maximum stitch length of 12 mm. The 867-190040 ECO is equipped with an oversized XXL vertical hook. The bobbin thread capacity increased by 70% makes it possible to reduce the number of bobbin changes nearly by half.
该机型为采用下送布、针送布和交替压脚上送布的单针锁式线迹平底板缝纫机，最大针距长度为12mm.867-190040经济型配置了垂直超大旋梭，梭芯线容量增加了70%，使更换梭芯的频率几可减半。
Results are as follows:(1) In order to increase the utilizition value of bamboo and to optimum the manufacture process, bamboo material should be cut into a certain length and be classified before using. Poor bamboo, small bamboo and the tip-parts of bamboo were also used to produce BOSB.(2) In the system of oriented flaking, the devices for pretreatment are the key, including block cutting and classification, longitudinal breaking, inner nodes eliminating, and oriented arrangement of bamboo pieces.(3) For the realization of auto-alignment, the auto-identifying and auto-correcting systems were designed to apply in real-time testing of production line. It could be used to adjust the right position of the surface and back of bamboo pieces, and to make sure their automatic arrangement in the same direction.(4) The key problem in oriented flaking was how to fix the position of bamboo pieces when it was forced to feed orderly into chipper to avoid their moving while flaking. Another problem was how to avoid strands smash. If strands were stricken in lateral, they were easily crushed due to the lower bonding strength between bamboo fibers.
对主要设备和设施进行了设计和分析，主要结果如下：(1)为了提高竹材的综合利用价值，优化生产工艺，将毛竹进行定段分级，利用次、小、梢竹材制造BOSB；(2)预处理设备是保证竹材定向削片的关键环节之一，包括竹材截段分级、纵向破竹、去内节、定向排列组坯设备；(3)为实现竹材毛坯自动化定位排列，设计了定向排列自动识别与纠正系统，用于生产线中实时检测，及时调整毛坯正反位置，实现相同方向依次自动排列；(4)竹材定向削片技术的主要难点为：①当竹材定向排列送入竹材削片机后，如何将竹条夹紧定位，防止其在切削过程中出现较严重的松动、散乱，保持较理想的方向排列；②如何减少切削过程中竹刨花的破碎是重要技术难点，因竹材具有纤维间结合强度低的特性，在切削形成竹刨花过程中，一旦竹刨花受到横向力的作用或撞击，易出现碎裂现象。
The effect of parameters such as weld groove, wire feed rate, welding speed, defocus length and gap weld formation was analyzed. The microstructure of joint was analyzed by metallographic obsveration and hardness test.
分析了工件坡口、焊接速度、送丝速度、离焦量、装配间隙等规范参数对焊缝成型影响；通过金相观察以及显微硬度测定分析了接头组织性能。
The same treatment was repeated on August 20th. 10 males served as controls. After 15 days of the first MLT treatment, the implanted animals grew faster, reached pelt maturity more quickly, reaching full prime 2 months before the controls and had a higher feed consumption than controls, while the pelt length was similar to the controls.
试验组狐(10只)于6月5日和8月20两次埋植褪黑激素，剂量均是2×6 mg，所有试验组狐于初次埋植后15天，与对照组相比，采食量明显增大，生长速度加快；9月末冬毛成熟，取皮，比对照组提前2个月，所产皮长度与对照组(11月末～12月取皮)差异不显著。
Feed the dog by hanging a piece of raw meat on a length of thread.
在绳子上吊块生肉来喂这只狗。
At the same time, the production of dry powder special putty mixers, feed mixer, sponge crusher and so on, clients may request the production length.
同时生产干粉腻子专用混合机，饲料搅拌机，海绵破碎机等，可按客户要求定尺制作。
The regressive equation between rape feed, cylinder line speed, cylinder length, and threshing and separating rate is established based on the test results using DPS and is simulated.
运用DPS数据处理系统对试验结果进行处理，建立了油菜喂入量、脱粒滚筒线速度、脱粒滚筒长度与脱粒分离率的回归方程，并进行了计算机仿真。
Real-time feed rate of the radiating pipe and length is measured by the tachometer roller transmitted via a communication cable to a servo controller.
散热管的实时速度和长度由测速轮测量，并由通信电缆传输给伺服控制器。