The diaphragm adopts 0.3-2mm sheet stainless steel with high strength to fabricate the assembly through to fabricate the assembly through riveting., on which there are 4-16 reaming holes, using bolts to connect the driving flange and the driven flange respectively.
其膜片采用0.3~2mm厚的特殊高强度不锈钢薄板铆制成组件，上面有4~16个铰制孔，用螺栓分别与主、从动法兰联结。
Comstruction features (1)Integration and direct connection deceleration motor, with low noises, small vibration, dust resistant, long life and high reliability; (2)The annular belt without joint can transport the materials smoothly and without leakage; (3)The flange at the end face for reducer is connected with the driving roller of the weighing scale directly, and it can simplify the design of the transmission part to make the installation very conveninet; (4)Particular design of spring leaf weighing mechanism and low electromagnetism gear speed detector, the weighing signals and the tachometer signals are accurate and stable; (5)Particular anti-meandering equipment for the belt; (6)The weighing scale is installed under the raw materials silo, and requires no electrical vibrating feeder or any other intermediate feeding facilities.
结构特点（1）一体化直联式减速电机，低噪音、低震动、抗粉尘、长寿命、高可靠性；（2）裙边环形无接头皮带，输送物料平稳、无漏料；（3）减速机端面法兰与秤体主动滚筒直接连接，简化了转动部分的设计，安装极其方便；（4）独特的簧片称量机构，以及独特的弱磁式齿轮侧速装置的设计，称重和测速信号准确稳定；（5）独特的皮带防跑偏装置；（6）称体安装在原料库下，无需电振动给料机或其它中间给料设备。
In case of rear wheel drive and four wheel drive vehicles drive train vibrations can be reduced by balancing the flange of the rear axle differential to give more driving comfort and an improved life of the vehicle.
如果能够平衡后轴法兰，就能减少后轮驱动以及四轮驱动车辆驱动部分的振动，并能不同程度增加驾驶舒适性，延长车辆寿命。
High viscosity gear pump bearings or the flange should be used instead of driving motor common installed base, foundation, bearing flange or need to have sufficient rigidity, to reduce operating gear pump when the vibration and noise.
高粘度齿轮泵的支座或法兰与其驱动电机应采用共同的安装基础，基础、法兰或支座均需具有足够的刚度，以减小齿轮泵运转时产生的振动和噪声。
Another one is to connect the injection pump to the driving gear with flange to avoid the influence from machining error of shaft and coaxial degree while installing.
二是将喷油泵与驱动齿轮间的连接方式改用法兰来连接，避免了由于轴的加工误差和安装同轴度的影响。
Drivers which position control and servo driving function was integrated was used as control driving component, rough locating was set up with laser bean. Flexible butt-joint assembly for precise flange in long and narrow space was realized with pinhole pickup camera.
用集成了位置控制和伺服驱动功能的驱动器作为控制驱动元件，利用激光束进行粗定位，针孔摄像机实现狭长盲视空间精密止口人工柔顺可视对接。
A tested prime motor is mechanically connected with a magnetic particle brake through driving steps, an instruction computer controls the output current of a power program controller, and the output current is used as the excitation current of the magnetic particle brake. A ball feed screw is arranged between a decelerator and a counterweight pan during the driving steps, and a cap nut covers on the ball feed screw. The holder of the ball feed screw is fixedly provided with a guide rail which is fixedly connected with the cap nut through a flange.
其被测试原动机通过传动环节与磁粉制动器机械连接，指令计算机控制电源程序控制器的输出电流，电源程序控制器的输出电流作为磁粉制动器的激磁电流，传动环节中在减速器和配重盘之间设有一滚珠丝杠，滚珠丝杠上套设一螺母，在滚珠丝杠的底座上固定一导轨，该导轨与螺母通过法兰固定连接。
2 The driving gear shaft relative to the mounting flange that only the mouth of the amount of radial runout should be consistent with design requirements.
3.2主动齿轮轴表明相对于安装法兰止口的径向圆跳动量，应符合设计要求。