Cylinder: Piston executive body of the air chamber, the piston cylinder in which the transport cover seal: Piston implementing agencies with the stent cylinder junction of the sealing elements.
气缸：活塞执行机构的气室，活塞在其中运气缸端盖密封：活塞执行机构气缸与支架的连接处的密封元件。
And the stress distribution of cylinder body produced by optimum technique was analyzed.
通过工艺改进，消除了关键部位的缩孔缺陷。
Control cylinder, uptilt move the tower body about 1.5m, as to supporting the two inner climbing stay bar on to climbing lug of the tower body.
7.4.4 操纵油缸，将塔身上移 1.5 米左右，将爬升框架上的两根内爬撑杆支撑在塔身踏步上。
The processing Parameters in overlaying welding copper alloy on the hydraulic cylinder body of grey cast iron are obtained through orthogonal testing method.
在灰口铸铁液压油缸活塞基体外圆用火焰堆焊Cu合金的研究过程中，采用正交试验法得出堆焊工艺参数。
Hydraulic pressure part consists of cylinder body around having some axial direction cylinders, pole piston, matching stream canister and timing equipment. Pyramidal difference decelerate part is composed of twin inner bevel wheel with difference of 2-toothes, twin outer bevel wheel without tooth difference and skew shaft etc.
液压驱动部分由周围均布有若干轴向缸的缸体、柱塞、配流筒及调速装置等组成，减速部分由二齿差内锥齿轮副和零齿差外锥齿轮周向限制副及歪轴等组成。
It is mainly fixed on the pump body from the bush, as well as placement in the pump cylinder screw, and the initiative with its meshing of screw driven by two components.
它主要是由固定在泵体中的衬套以及安插在泵缸中的主动螺杆和与其啮合的两根从动螺杆所组成。
This topic is the design of general scheme and right headstock of modular machine tool for precision drill holes on three-side of diesel cylinder body.
本课题设计一台加工柴油机气缸体的三面钻削组合机床，主要完成机床总体和右主轴箱的设计工作。
The cylinder body of the compressor draws out hot air and sends it to the rear part of the rain hood, serving as anti-icing function during winter.
压气机缸体上抽出热空气至防雨罩后面，在冬季时起到防冰冻作用。
Vice-valve installed in the main valve side or both sides of the flap valve and the screw connection, the normal flow of media, the valve is opened, the medium pressure valve is opened by the Deputy, the medium through the valve hole into the main Double Door Check Valves, Air Cushion valve, Vice export side, so that the main valve inlet end of relief, the main valve valve flap to open, the main valve before and after the pressure balance; medium counter-current, the main valve valve valve in the counterflow medium under the action of fast closed, and the deputy valve body upper part of the buffer tank, the Deputy valve valve cap screwed the upper part of his body covered with a small hole, the Deputy valve valve valve with the piston rod sets have a certain air gap between the piston and the buffer cylinder with rubber O-ring seal, the piston and the valve flap between the lower-dimensional seal; as Vice-valve With the main valve valve valve valve valve was closed, because of Vice-valve valve cover the role of holes, the medium gradually flows through the small hole on the Vice-valve cylinder cushion cavity, part of the media, through the Deputy valve valve flap and the gap between the piston rod reflux, it is slow, Vice valve piston closed.
副阀安 装在主阀阀瓣下侧或两侧且用螺纹联接，介质正常流动阀门开启时，介质压力将副阀打开，介质通过副阀小孔流入主阀出口端，使主阀进水口端卸压，主阀阀瓣开启，主阀前后压力趋于平衡；介质逆流时，主阀阀瓣在逆流介质作用下快速关闭，而副阀阀体上部为缓冲缸，副阀阀盖旋入阀体上部其盖上有一小孔，副阀阀瓣与其活塞杆空套有一定间隙，活塞与缓冲缸之间采用O型橡胶圈密封，活塞下部与阀瓣之间为平面密封；当副阀阀瓣随主阀阀瓣关闭而关闭时，因副阀阀盖小孔的作用，介质通过小孔逐渐流入副阀缓冲缸上腔体，一部分介质通过副阀阀瓣与活塞杆之间的间隙倒流，故副阀活塞是缓慢关闭的。
The simulation results show that: during lowering of lifted tipping body, (2n+1) hydraulic pressure peaks occur in the larger chamber of lifting cylinder of empty truck.(n is the number of stages of the cylinder). The higher the engine speed is, the stronger the hydraulic impact is.
仿真结果显示：货箱举升回落过程中，举升液压缸无杆腔内先后出现(2n+1)个油压峰值，发动机转速越高，油压冲击越大。
The invention relates to a tappet rotational spacing of roller type used for an engine, which consists of a cylinder body, a roller tappet and a cam shaft and is characterized in that: a positioning key is arranged on the top surface of the cylinder body of the engine, which is fixed in in a positioning slot of the cylinder body, and the side plane of the positioning key matches with the small platform on a tappet.
本发明涉及一种发动机滚子式挺柱转动限位，由缸体，滚子挺柱及凸轮轴组成，其特征在于：在发动机缸体顶面安装定位键，定位键固定在缸体的定位槽中，定位键的侧平面和挺柱上小平台的配合。
According to the cylinder body size, the shape, the material, processing request and so on spot structure and processing precision, surface roughness, determined selects the horizontal-type two-sided mill aggregate machine-tool; In order to realize the work piece to enter quickly with the labor enters matches by moves the work table; Is processed the plane is the big plane, the material is HT250, therefore cutting tool choice hard alloy face cutter.
根据气缸体尺寸、形状、材料、加工部位的结构和加工精度、表面粗糙度等要求，确定选用卧式双面铣组合机床；为实现工件快进和工进配以移动工作台；被加工平面为大平面，材料为HT250，故刀具选择硬质合金端铣刀。
It has also been clear that the source of piston knock noise is the impact between piston and cylinder sleeve by the vibration acceleration of the engines body surface.
明确了低转速时，燃烧噪声占主导地位；高转速时，活塞敲击噪声占主导地位。
Outrigger frame with four vertical, Hydraulic cylinder can support the expansion of the body, So off track after track frame for the expansion, which reduce the frictional resistance, So that the expansion of the track action more stable and reliable.
车架装有四个垂直支腿，可以通过液压油缸的伸缩支撑起车身，使履带离地后再进行履带架的伸缩，其摩擦阻力减小，从而使履带的伸缩动作更加平稳可靠。
Supplies the engine pure part: The piston unit, the connecting rod, the crank module, the piston curl, the connecting rod tile, the host axle bush, stop push around the piece, the crank the oil seal, the cylinder bed, the oil sump filling piece, the gear room filling piece, the water pump filling piece, to enter the exhaust gate, the valve-seat ring, the air valve guide, the tire valve oil seal, the fuel pump unit, the plunger matching part, the bean matching part, the turbosupercharger, the cylinder cover unit, the crank case body, filters, Chai Lv, the generator, the generator, the water pump, the water pipe spatially and so on.
供应发动机纯正部件：活塞总成、连杆、曲轴组件、活塞环、连杆瓦、主轴瓦、止推片、曲轴前后油封、缸床、油底壳垫片、齿轮室垫片、水泵垫片、进排气门、气门座圈、气门导管、气门油封、燃油泵总成、柱塞偶件、喷油嘴偶件、涡轮增压器，气缸盖总成，曲轴箱体，空滤、柴滤、发电机、起动机、水泵、水管等。
Rated weight from 6T, or highly rated from 20M, hydraulic cylinder four-shen crane, 1300mm plate in rodents, single-stage planetary gear-type hoisting mechanism, high-strength body-wide rotary-Worm turning operations, Chase Drive Central turn the whole body turning operations.
额定起重量6T，额定起升高度20M，液压油缸四级伸吊臂，1300mm内啮齿盘，单级行星齿轮式起升机构，高强度蜗轮式回转机构全回转作业，大通径中央回转体全回转作业。
The company's automotive brake and wheel drive shaft assembly, the locomotive of the cylinder vehicle braking systems, Pistons, three, four-way valves, and other important body parts and components sold to the United States, Germany, Canada and other countries, in more than 50 million products.
本公司生产的汽车刹车毂及传动轴总成，机车车辆刹车系统的汽缸、活塞、三通、四通气阀体等重要零、部件远销美国、德国、加拿大等国，年产品能力50多万套。
Four rectangular 8° interbody fusion cage models and one cylinder 0° interbody fusion cage model created according to the anatomic geometry the intact L4-5 model were used to simulate a 150N compressive preload with interfacial friction coefficient of 0.4 for the study of interaction between implants and vertebral body. Then L3 vertebral body was subjected to 10-Nm moment in flexion, extension, lateral bending and torsion, respectively. The nodes on the bottom surface of L4 were constrained.
由 L3-L4原始椎体模型修改四种8度之矩型椎间融合器及一种0度之圆柱型椎间融合器，给予150N 模拟自重而植入物与椎体界面摩擦系数设定为0.4，在 L3椎体给予10Nm 力矩，分别模拟前弯、伸展、侧弯及扭转负载，并固定 L4椎体底部所有节点。
The spindle selects enclosed rolling bearing for supporting; vertical and horizontal drag board are adopted with enclosed rolling rod drive; body guide ways are casted with abrasion-resistance iron quenched with super frequency and milled precisely, and all these contribute to a long-term processing precision and a long lifespan; 5.5KW motor serves as the main motor contribute to a stronger turning capacity and larger rotary speed range; Workpiece clamping is are adopted withed with spring collet, it can also be equipped with hydraulic chuck, four-spindle oil cylinder, pneumatic, hydraulic tail stock.
CK6232数控车床是一款高刚性封密数控车床，特别适宜粗精加工，整机造型稳重大方，全封闭护罩防护，主轴采用精密刚性轴承支撑，纵横向拖板采用精密滚珠丝杆传动，床身导轨采用耐磨铸铁铸造，经超音频淬火及精密磨削，能长期稳定的保证加工精度和使用寿命；主电机选用5.5KW 的电机，使主轴有更强的切削能力和转速范围；工件装夹方式选用弹簧夹头，也可按用户要求配置手动卡盘、液压卡盘，气压、液压尾座。
The product is mainly applied in:counticaster machine in mutallurgy industry, cement machine and screw type moving rail etc. hydraulic pressure lubricant pump industry, mesohigh gear lubricant pump, displacement pump, vane pump etc. automobile industry:automobile shock absorber, hydraulic, pressur hydro cylinder, universal machine industry:printing machine, spinning machine, foodstuff machine, tobacco machine, body-building machine etc.
该产品广泛应用于：冶金行业连铸扎机，水泥机械和螺旋式输送机等；液压油泵行业：中高压齿轮油泵、柱塞泵、叶片泵等；汽车行业：汽车减震器、液压油缸等；通用机械行业：印刷机械、纺织机械、食品机械、烟草机械、健身器材等。