Based on the analysis of plastic flow law in crankshaft forming, the cause of typical forming defects, i. e. the folding existing in the crankshaft pin and crank arm was found out.
通过模拟分析曲轴成形的塑性流动规律，找出了大型船用曲轴曲拐成形过程中的典型缺陷连杆颈和曲柄臂外侧折叠的成因。
Measurable bearing rings, needle, roller, ball, electrical axis, electrical commutator, spline shaft, gear shaft, camshaft, crankshaft, cylinder pin, piston pin, piston, cylinder liner, valve, valves, gears, cam, oil pump glib, hydraulic parts, pneumatic parts, textile machinery fittings, such as workpiece-related parameters; applicable to scientific research institutes, universities, institutions and enterprises measurement metrology room, workshop and so on.
可测轴承套圈、滚针、滚子、钢球、电机轴、电机换向器、花键轴、齿轮轴、凸轮轴、曲轴、圆柱销、活塞销、活塞、缸套、气门、阀门、齿轮、凸轮、油泵油嘴、液压件、气动件、纺机配件等工件相关参数；适用于科研院所、大专院校、计量机构和企业计量室、车间等。
Before the crankshaft pin is punched into its position, the pin and the front and rear crank journals must be washed with the washing petrol blended with 1 & 2% of lubricants.
在压入曲轴销前应当用掺有1%～2%润滑油的洗涤汽油将曲柄销和前后曲柄颊清洗干净并吹干。润滑油不能掺得过多，多了会影响组装后的紧配合程度。
Influence of Constraint Condition on FEA for Split - Pin Crankshaft
约束条件对错拐曲轴有限元分析的影响
CKP sensor rotor plate is fitted to crankshaft counterweight No.1 by pin and screws.
转子板的CKP传感器安装在曲轴销和螺钉重第一。
The fillets of crank pin and main journal have a relatively weak strength. In establishing the grid model for crankshaft, these fillets need to be refined.
曲柄销与主轴颈的圆角为强度较薄弱部位，在建立曲轴网格模型时，需要对这些圆角处进行细化。
To prevent the loss of oil, place the seals at both ends the crankshaft where it extends through the crankcase. When main bearings are replaced, tighten the bearing cap to the proper tension with a torque wrench and lock them in place with a cotter pin or safety wire after they are in place.
为防止损失的油，放在密封的两头曲轴而延伸，通过曲轴箱，当主轴承更换，收紧轴承盖，以适当的张力与扭力扳手，并锁定他们放在一起特引脚或安全线后，他们都已具备。
Before the crankshaft pin is punched into its position, the pin and the front and rear crank journals must be washed with the washing petrol blended with 1 & 2 % of lubricants.
在压入曲轴销前应当用掺有1%～2%润滑油的洗涤汽油将曲柄销和前后曲柄颊清洗干净并吹干。润滑油不能掺得过多，多了会影响组装后的紧配合程度。
Inertia ring of front shock absorber also serves as a belt pulley; through the locating pin and 8 blots on its spider, rear shock absorber is fixed on wheel hub of front shock absorber; the shock absorber assembly composed by the two shock absorbers is installed at front end of crankshaft interference-fitting with wheel hub of front shock absorber and is also equipped with the bolts with tightening torque of 285N. m.
前减振器的惯性环兼作皮带轮用，后减振器通过其中心盘上的定位销和8个螺栓固定在前减振器的轮毂上，二者组成的减振器总成与前减振器轮毂过盈配合装于曲轴前端，并配有螺栓，拧紧力矩为285N.m。